Please enable JavaScript to view this site.

10-pin CoreSight (1.27mm) Debug Adapter

 

Click to expand

 

 

Ordering code

IC50116-2

This debug adapter is used to connect the iC5000 and the iC5700 BlueBox to the Cortex based target. It’s used to connect to the embedded target featuring a 10-pin 1.27mm target debug connector with the Arm CoreSight 10 pinout. Current version was renamed from Cortex Debug Adapter.

 

The following pinout is valid on the target side:

Signal Direction

Signal Description

Signal

Pin

Pin

Signal

Signal Description

Signal Direction

I

Reference Voltage

Vref

1

2

SWDIO/TMS

SWD/JTAG

I/O / O

 

Ground

GND

3

4

SWCLK/TCK

SWD/JTAG

O

 

Ground

GND

5

6

SWO/TDO

SWD/JTAG

I

 

Not Connected

KEY

7

8

NC/TDI

Not Connected /JTAG

O

 

Ground

GND

9

10

nRESET

Reset

I/O

10-pin ARM CoreSight pinout

 

Signal Direction is described from the BlueBox perspective.

 

The debug adapter features resettable fuses on pins 1, 2, 4, 6, 8 and 10. These fuses protect debug signals against overcurrent and cycle back to a conductive state after the excessive current fades away.

 

10-pin 1.27mm connectors

Warning_orange

The debug adapter connects to the target through one of the two 10-pin 1.27mm connectors. Note that only one is to be connected to the target!

 

Strain relief

The robust connector (Samtec FFSD-05-01-N-SR) is located at the end of the cable and is the recommended connection connector. It's a bit wider and therefore the target must have a matching part populated. Matching part on the target side is e.g. Samtec ESHF-105-01-L-D (full frame connector) or Samtec FTSH-105-01-F-DV-K (connector without the frame at the side).

 

Standard type

The second connector (Samtec FFSD-05-01-N) is 1cm away from the first one toward the BlueBox (Samtec FFSD-05-01-N). It’s much less robust and is prone to fail if the cable is not handled cautiously or just connected/disconnected too many times. This connector should be used when the target doesn’t provide the matching target connector for the Strain relief type connector. Matching part on the target is Samtec SHF-105-01-L-D or Samtec FTSH-105-01-F-DV-K (connector without the frame at the side).

 

For the target side connector it’s most convenient to use the FTSH-105-01-F-DV-K connector since it matches the connector with and without the Strain relief option.

 

 

Target connector

strain-relief

strain-relief2

 

Robust and less prone to fail

×

strain-relief3

With frame without strain relief

(SHF-1xx-01-L-D)

×

strain-relief4

Without frame

(FTSH-1xx-01-L-DV)

strain-relief5

With frame with strain relief

(ESHF-1xx-01-L-D)

 

Additional cable

If the 10-pin 1.27mm pitch cable gets damaged or you need longer cables, it can be ordered as a spare part under the ordering code:

IA10PIN10PIN127

IA10PIN10PIN127-REV - Reversed connectors

IA10PIN10PIN127-CUST - Custom cable length must be specified at the order

IA10PIN10PIN127-CUS1 - Reversed connectors

IA10PIN10PIN127

Warning_orange

Note that the optional length should be reasonable (e.g. 10 cm) since the quality of electrical signals degrades with prolonging the cable.

 

i-icon

BlueBox functionality with this cable, intended for rare situations when the standard debug adapter cannot connect to the target due to physical obstacles, is not guaranteed. Using the BlueBox at lower debug frequency scan speeds without trace functionality may be an acceptable compromise. You should test the BlueBox with a custom-length ribbon cable to ensure compatibility with winIDEA.

 

 

i-icon

Make sure this adapter fits on your target connector - check Cross Table.

 

 

i-icon

Refer to Hardware Setup and Configuration Tutorial to get more information on how to connect the hardware.

 

Copyright © 2024 TASKING