Samtec22 to HSTCU (USB-C) Converter
This converter is used to connect Infineon AGBT Active Probe (Ordering code: IC57164) to the TriBoards with HSTCU (High Speed Tool Connector USB-C). It must be ordered separately.
When attaching this converter to the Active Probe, make sure its marking A and marking B is aligned and matches with the markings on the Active Probe connector. |
The following pinout is valid on the converter side:
Signal Direction |
Signal Description |
Signal |
Pin |
Pin |
Signal |
Signal Description |
Signal Direction |
---|---|---|---|---|---|---|---|
I |
AGBT TX0_P |
TX0+ |
1 |
2 |
Vref |
Reference Voltage |
I |
I |
AGBT TX0_N |
TX0- |
3 |
4 |
DAP0 |
DAP clock |
O |
O |
Ground |
GND |
5 |
6 |
DAP1 |
DAP Data pin |
IO |
|
AGBT TX0_P |
TX1+ |
7 |
8 |
DAP3 |
Optional 3rd Data pin |
IO |
|
AGBT TX_N |
TX1- |
9 |
10 |
DAP2 |
Optional 2nd Data pin |
IO |
|
Ground |
GND |
11 |
12 |
nTRST/DAPEN |
Output |
O |
|
Not Connected |
NC |
13 |
14 |
CLK+ |
AGBT Clock |
O |
|
Not Connected |
NC |
15 |
16 |
CLK- |
AGBT Clock |
O |
|
Ground |
GND |
17 |
18 |
NC |
Not Connected |
|
|
Not Connected |
NC |
19 |
20 |
NC |
Not Connected |
|
|
Not Connected |
NC |
21 |
22 |
nRESET |
Target Reset Pin |
IO |
22-pin Aurora pinout
The following pinout is valid on the target side:
Signal Direction |
Signal Description |
Signal |
Pin |
Pin |
Signal |
Signal Description |
Signal Direction |
---|---|---|---|---|---|---|---|
|
Ground |
GND |
A1 |
B12 |
NC |
Not Connected |
|
I |
AGBT TX0_P |
TX0+ |
A2 |
B11 |
CLK+ |
AGBT Clock |
O |
I |
AGBT TX0_N |
TX0- |
A3 |
B10 |
CLK- |
AGBT Clock |
O |
|
Not Connected |
NC |
A4 |
B9 |
NC |
Not Connected |
|
I/O |
Target Reset Pin |
nRESET |
A5 |
B8 |
DAP1 |
DAP Data |
I |
I/O |
Optional 2nd DAP data |
DAP2 |
A6 |
B7 |
nTRST |
Output |
O |
I/O |
Optional 3rd DAP data |
DAP3 |
A7 |
B6 |
NC |
Not Connected |
|
O |
DAP Clock |
DAP0 |
A8 |
B5 |
Vref |
Reference Voltage |
I |
|
Not Connected |
NC |
A9 |
B4 |
NC |
Not Connected |
|
|
Not Connected |
NC |
A10 |
B3 |
NC |
Not Connected |
|
|
Not Connected |
NC |
A11 |
B2 |
NC |
Not Connected |
|
|
Ground |
GND |
A12 |
B1 |
GND |
Ground |
|
(HSTCU) USB-C pinout
Blue colored signals are trace signals.
Signal Direction is described from the BlueBox perspective.
When initially connecting the BlueBox to a target, ensure the debug adapter pinout matches the Target connector to avoid potential hardware failure. |